Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 59 matches
924Board.org Forum Index
Author Message
  Topic: Help with my high beam switch
16again2009

Replies: 4
Views: 691

PostForum: General Discussions   Posted: Tue May 24, 2022 4:10 am   Subject: Help with my high beam switch
The high/low beam switch is two parts. It has kind of a claw that snaps into the back part. You didn't get that connected when you put it back together. Take it apart again and snap the claw from the ...
  Topic: Washers not working, race to pass MOT 😨😨
16again2009

Replies: 7
Views: 1694

PostForum: 924S Discussions   Posted: Fri Apr 29, 2022 7:18 pm   Subject: Washers not working, race to pass MOT 😨😨
Happy I could help. Good Luck.
  Topic: Washers not working, race to pass MOT 😨😨
16again2009

Replies: 7
Views: 1694

PostForum: 924S Discussions   Posted: Fri Apr 29, 2022 6:20 pm   Subject: Washers not working, race to pass MOT 😨😨
If you're sure you got the claw hooked up, the only thing I can think of is a fuse
  Topic: Washers not working, race to pass MOT 😨😨
16again2009

Replies: 7
Views: 1694

PostForum: 924S Discussions   Posted: Thu Apr 28, 2022 4:47 pm   Subject: Washers not working, race to pass MOT 😨😨
I have a 1988 924s and had this problem a few years ago. I pulled the steering wheel. At the top there is a small copper tab. When you pull the wiper handle back, it moved this tab to make contact wit ...
  Topic: 88 Porsche 924s new cat w/ or without 02 sensor port?
16again2009

Replies: 1
Views: 2683

PostForum: 924S Discussions   Posted: Tue Feb 01, 2022 5:10 am   Subject: 88 Porsche 924s new cat w/ or without 02 sensor port?
I just looked under my 1988 924s. The o2 sensor is on the header pipe, not the cat. It only has one 02 sensor.
  Topic: No go ??
16again2009

Replies: 6
Views: 5920

PostForum: 924S Discussions   Posted: Mon Oct 11, 2021 4:17 pm   Subject: No go ??
I bought a 1988 924s a few years ago. When I got it running it did the same as yours. It was the rubber clutch disc. Its a big job to change. Good Luck.
  Topic: 1987 924s 5spd poor/no acceleration when hot
16again2009

Replies: 9
Views: 11245

PostForum: 924S Discussions   Posted: Mon Oct 11, 2021 2:14 am   Subject: 1987 924s 5spd poor/no acceleration when hot
there is a guy on the pelican forum that had sort of the same problem as you, but not exactly. It turned out to be his o2 sensor. You might check that. Just unplug it and see if it runs better.

.pe ...
  Topic: 1987 924s 5spd poor/no acceleration when hot
16again2009

Replies: 9
Views: 11245

PostForum: 924S Discussions   Posted: Thu Sep 30, 2021 2:46 am   Subject: 1987 924s 5spd poor/no acceleration when hot
Did you figure the problem out?
  Topic: Brake bleeding
16again2009

Replies: 1
Views: 3716

PostForum: General Discussions   Posted: Sun Aug 01, 2021 2:32 pm   Subject: Brake bleeding
I would bleed at least one of them to make sure your master cylinder is moving fluid. If it doesn't, that's your problem.
  Topic: 1987 924s annoying wiper switch issue
16again2009

Replies: 2
Views: 5747

PostForum: Body and Interior   Posted: Fri Jul 30, 2021 11:59 am   Subject: 1987 924s annoying wiper switch issue
I have had some experience with this. If you look in the crack between the steering wheel and the hub, from the top, you will see a small metal tab. You need to bend it a little bit so it makes contac ...
  Topic: water pump 924s
16again2009

Replies: 5
Views: 10034

PostForum: 924S Discussions   Posted: Sat Feb 13, 2021 2:45 pm   Subject: water pump 924s
Did you find the problem?
  Topic: water pump 924s
16again2009

Replies: 5
Views: 10034

PostForum: 924S Discussions   Posted: Fri Feb 05, 2021 7:12 am   Subject: water pump 924s
Van Svenson has a 3 part video about changing the belts and the water pump. Its on a turbo but the process is the same. It shows everything you will ever need to know in this area. see attached link. ...
  Topic: water pump 924s
16again2009

Replies: 5
Views: 10034

PostForum: 924S Discussions   Posted: Fri Feb 05, 2021 7:00 am   Subject: water pump 924s
Can you give a better description of the noise. Is it whining, squealing, banging?
  Topic: turn signal assembly
16again2009

Replies: 1
Views: 11603

PostForum: 924S Discussions   Posted: Sun Aug 23, 2020 8:57 am   Subject: turn signal assembly
I figured it out. You have to remove the bumper guard to get to the inboard screw.
  Topic: turn signal assembly
16again2009

Replies: 1
Views: 11603

PostForum: 924S Discussions   Posted: Wed Aug 19, 2020 11:37 am   Subject: turn signal assembly
1988 924s. How do I remove the front driver's side turn signal assembly. Do you have to remove the bumper or bumper guard. I can't figure out how to get to that inside screw.
 
Page 1 of 4 Goto page 1, 2, 3, 4  Next
All times are GMT + 10 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group