Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

First day on Track

 
Post new topic   Reply to topic    924Board.org Forum Index -> 924 Racing Today
View previous topic :: View next topic  
Author Message
MikeJinCO  



Joined: 08 Jun 2010
Posts: 927
Location: Maysville, Colorado

PostPosted: Mon Jul 15, 2019 7:56 am    Post subject: First day on Track Reply with quote

Friday went down to an open lapping day at the Pueblo, CO track, about 2.2mi and primarily flat. I joked how the car has been driven about 100 yards around the driveway this century, it was a true derelict. It actually ran quite well, started off driving the parking lot at 15mph then out on the track. Amazingly nothing fell off. The wheels required multiple torquing as all the studs were new. The oil temperatures got up to about 250F before the cooler with 6 bar pressure. Water temps stayed at 180F. I currently have some old stock type brake pads on the 944 caliper/rotors and it stopped amazingly well compared to the stock disc/drum 924. It seemed to run straight down the road and not pull to the side, I frankly don't know enough to judge understeer/oversteer at this point, but nothing was obvious. The amazing thing was the power, it really accelerated compared to a stock 924. I have about 10.1 compression using the 931S2 pistons with a mildly ported NA head with about .045 quench, an Elgin 66-15 cam(262deg), MSDS headers, and 45mm Webers.

I found the usual assortment of problems, I have a Wink 5 panel mirror mounted to the cage and it is just in the way and too big. A Longacre convex mirror is probably in my future, it has to be cage mounted due to a lexan windshield. The 45mm Webers need the throttle return much stronger as it doesn't shut down well when off throttle. I'm going to change out the seat as ancient, short legged me can't get out over the Kirkey side bolster and NASCAR door bars fast enough. I have the 1980 Dp front end which is under 4" off the ground so getting this guy loaded on a trailer is a real trick due to an approach angle of about 8deg.

First race will be High Plains Raceway on Aug 11/12 and I need to get the carbs squared away better, I'm unhappy with the ignition timing and I'd like to go to a no mechanical advance distributor, but the distributor might need indexing one tooth and I am unclear on how to make that all work. I'll also get some better brakes (I doubt I ever got them really hot on Friday) check the alignment-again. and basically check every bolt.
_________________
Mike
Poco a Poco, #033 '78 Vintage racer, SCCA Dp-81
'77 924
cricketdesigns.com
Back to top
View user's profile Send private message Visit poster's website
924RACR  



Joined: 29 Jul 2001
Posts: 8334
Location: Royal Oak, MI, USA

PostPosted: Mon Jul 15, 2019 10:23 pm    Post subject: Reply with quote

Sweet!
_________________
Vaughan Scott
Webmeister
'79 924 #77 ITB racecar
'82 931 Plat. Silver
#25 Hidari Firefly P2 sports prototype
Back to top
View user's profile Send private message Send e-mail Visit poster's website
MikesCoupeGT  



Joined: 18 Oct 2006
Posts: 469
Location: Ontario Canada

PostPosted: Tue Jul 16, 2019 12:44 am    Post subject: Reply with quote

Can't wait to see some action shots. The car sounds awesome.
_________________
Cheers;
MikesCoupeGT
'76 924
'83 944
''19 Elantra GT N-Line
Back to top
View user's profile Send private message Yahoo Messenger MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic    924Board.org Forum Index -> 924 Racing Today All times are GMT + 10 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group