Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Wanted for 931: Rubber pipe between Air Flow Meter and Turbo

 
Post new topic   Reply to topic    924Board.org Forum Index -> Cars and Parts Wanted/For Sale
View previous topic :: View next topic  
Author Message
Johann  



Joined: 07 Aug 2016
Posts: 173
Location: Netherlands

PostPosted: Sat Aug 18, 2018 6:18 am    Post subject: Wanted for 931: Rubber pipe between Air Flow Meter and Turbo Reply with quote

I have a ripped bellow on my 931 The part number is 93111013804 and naturally it is NLA.



Does anybody have a good one for sale? Or do you have an alternative solution?

Thanks!
Back to top
View user's profile Send private message AIM Address
Johann  



Joined: 07 Aug 2016
Posts: 173
Location: Netherlands

PostPosted: Sun Aug 19, 2018 7:46 pm    Post subject: Reply with quote

Bump

I have glued the tair, but I don't think it is going to last long. Any help would be appreciated.

I have looked into having a pipe custom made out of silicone, but that is quite expensive. But looking at it, I wonder if this is not just a standard width with a standard angle?

I would appreciate any advice.
Back to top
View user's profile Send private message AIM Address
CÚdric  



Joined: 27 Aug 2004
Posts: 1728
Location: Sweden

PostPosted: Sun Aug 19, 2018 9:20 pm    Post subject: Reply with quote

There have been several people on here that have gone with a silicon hose, try searching the forum ń.
_________________
┤79 924
http://www.garaget.org/show.php?car=211
┤80 924 Turbo
http://www.garaget.org/?car=160275
Back to top
View user's profile Send private message MSN Messenger
Kenodog  



Joined: 25 Jun 2003
Posts: 2438
Location: Vancouver,B.C.

PostPosted: Tue Aug 21, 2018 5:25 am    Post subject: Reply with quote

You can use silicone but beware that because of the location and the fact these cars run oily the silicone will degrade in not very long. Oil kills silicone...



Me
_________________
1979 Euro 931, Olive
1981 931, Sabine
2014 Mazda CX-5 (Kid's limo)
2008 GS500
1996 Dodge Caravan (DJV)
Back to top
View user's profile Send private message Send e-mail MSN Messenger
Johann  



Joined: 07 Aug 2016
Posts: 173
Location: Netherlands

PostPosted: Thu Aug 23, 2018 7:09 pm    Post subject: Reply with quote

Thanks for the advice guys!

@Kenodog, my engine is dry on the outside. Something I am very proud of But I think you are refering to the oil comming through the intake via the crank breather pipe?

It looks like this is a good alternative.



And at about 15 euro a pop I am happy to replace it with every oil service
Back to top
View user's profile Send private message AIM Address
Dutch924-racer  



Joined: 23 Jul 2007
Posts: 1005
Location: The Netherlands

PostPosted: Fri Aug 24, 2018 3:20 am    Post subject: Reply with quote

I am using silicone, works to fine!
_________________
937 trackday car
Series 2 engine
951S turbo and intercooler
937 DITC
Fast road camshaft
Forge recirculation valve + boost controller
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    924Board.org Forum Index -> Cars and Parts Wanted/For Sale All times are GMT + 11 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group