Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 8286 matches
924Board.org Forum Index
Author Message
  Topic: Fuel starvation?
Paul

Replies: 5
Views: 143

PostForum: 931 Tech.   Posted: Wed Dec 13, 2017 6:58 am   Subject: Fuel starvation?
My 1980 931S (long gone) did this years ago, in my case it was caused by the fuel filter being installed backwards by the PO.
  Topic: Aftermarket Front Valance
Paul

Replies: 2
Views: 614

PostForum: Body and Interior   Posted: Thu Dec 07, 2017 1:25 pm   Subject: Aftermarket Front Valance
Part #5


https://www.sunsetporscheparts.com/auto-parts/1987/porsche/924/s-trim/2-5l-l4-gas-engine/body-cat/front-panel-scat
  Topic: Horn doesn't work
Paul

Replies: 3
Views: 730

PostForum: 931 Tech.   Posted: Sun Nov 26, 2017 7:05 am   Subject: Horn doesn't work
Make sure the horn works by giving it 12 volts....
  Topic: Found me a Weissach
Paul

Replies: 28
Views: 2330

PostForum: General Discussions   Posted: Sun Nov 26, 2017 7:03 am   Subject: Found me a Weissach
That AA engine has rust in the bores....stay away from AA.
  Topic: Early 924 turbo for sale
Paul

Replies: 13
Views: 566

PostForum: Cars and Parts Wanted/For Sale   Posted: Wed Nov 22, 2017 12:12 pm   Subject: Early 924 turbo for sale
Wow, that has to be one of the best survivor 931s in existence!
  Topic: No Warning lights
Paul

Replies: 3
Views: 328

PostForum: General Discussions   Posted: Tue Oct 31, 2017 3:38 am   Subject: No Warning lights
Hopefully you had the fuel pump disabled while doing this cranking...
  Topic: How to measure clutch ware
Paul

Replies: 4
Views: 307

PostForum: 931 Discussion   Posted: Sun Oct 29, 2017 11:38 am   Subject: How to measure clutch ware
I usually keep trying different sized sockets until I find one that just fits, then I measure its outer diameter.

34mm - 18mm = 16mm. So if it measures 26mm for example, it's at 50%.
  Topic: Won't start, coming off engine rebuild
Paul

Replies: 5
Views: 364

PostForum: General Discussions   Posted: Sun Oct 29, 2017 9:25 am   Subject: Won't start, coming off engine rebuild
Absolutely will cause the issue. On NA cars I've seen the clutch cable melt and snap when trying to start the motor with this ground disconnected.
  Topic: How to measure clutch ware
Paul

Replies: 4
Views: 307

PostForum: 931 Discussion   Posted: Sun Oct 29, 2017 5:05 am   Subject: How to measure clutch ware
Yes.

http://www.clarks-garage.com/shop-manual/clutch-03.htm
  Topic: Won't start, coming off engine rebuild
Paul

Replies: 5
Views: 364

PostForum: General Discussions   Posted: Sun Oct 29, 2017 4:47 am   Subject: Won't start, coming off engine rebuild
Make sure you have installed the engine ground wire from the coil area to the block properly.
  Topic: mystery gas leak
Paul

Replies: 11
Views: 561

PostForum: General Discussions   Posted: Mon Oct 23, 2017 1:24 pm   Subject: mystery gas leak
Most likely a crack on top of the fuel tank or a leaking rubber fuel vent line that only leaks when the tank is full and pressurized.

Some of us never tighten the gas cap the whole way to avoid pre ...
  Topic: Clarks Garage
Paul

Replies: 12
Views: 768

PostForum: General Discussions   Posted: Mon Oct 16, 2017 1:37 pm   Subject: Clarks Garage
RIP, very sad news.
  Topic: Uh oh...just bought an '82 931!
Paul

Replies: 11
Views: 822

PostForum: 931 Discussion   Posted: Sun Oct 08, 2017 7:10 am   Subject: Uh oh...just bought an '82 931!
Find and correct the oil leak that's coating the tranny.

https://bringatrailer.com/wp-content/uploads/2017/09/IMG_6774-1-155x105.jpg

https://bringatrailer.com/wp-content/uploads/2017/09/IMG_6774 ...
  Topic: '78 924 Eaten by Harvey
Paul

Replies: 5
Views: 593

PostForum: Body and Interior   Posted: Sun Sep 17, 2017 1:26 pm   Subject: '78 924 Eaten by Harvey
Beware of mold, it grows very quickly in warm weather.
  Topic: My 1980 931 4 bolt turbo need some info and advise
Paul

Replies: 59
Views: 3823

PostForum: General Discussions   Posted: Sun Sep 17, 2017 1:16 pm   Subject: My 1980 931 4 bolt turbo need some info and advise
Make sure you bleed the cooling system if you haven't already. Air pockets will cause overheating.
 
Page 1 of 553 Goto page 1, 2, 3 ... 551, 552, 553  Next
All times are GMT + 11 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group