Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 995 matches
924Board.org Forum Index
Author Message
  Topic: Five-speed conversion
MikeJinCO

Replies: 8
Views: 414

PostForum: Performance Upgrades   Posted: Thu Feb 22, 2024 7:58 am   Subject: Five-speed conversion
I just checked and the early 944 and late 924 5 speed shift rods have the same PN. Clarks Garage.com is a great reference. I took my donor 5 speed out in the middle of a field so it was a bit tricky ...
  Topic: Five-speed conversion
MikeJinCO

Replies: 8
Views: 414

PostForum: Performance Upgrades   Posted: Thu Feb 22, 2024 2:11 am   Subject: Five-speed conversion
The above is correct but you must be a little careful with this as if I recall correctly the USA gearbox sequence vs the ROW sequence might be different. In the US the final drive ratios for the NA ...
  Topic: Injector plug size? turbo head w/ carbs
MikeJinCO

Replies: 4
Views: 506

PostForum: Performance Upgrades   Posted: Thu Dec 21, 2023 11:54 pm   Subject: Injector plug size? turbo head w/ carbs
Update, 22mm from McMaster Carr get the ones with a sunken hex heads as the flanged one won't seal.
  Topic: Injector plug size? turbo head w/ carbs
MikeJinCO

Replies: 4
Views: 506

PostForum: Performance Upgrades   Posted: Tue Dec 19, 2023 10:29 pm   Subject: Injector plug size? turbo head w/ carbs
When I was modifying heads I fund some I think from Belmetric Bolt. As I recall either 21 or 22mm. Measure with calipers, It is a metric pipe plug. PM sent
  Topic: What master cylinder for 5 lug conversion
MikeJinCO

Replies: 3
Views: 427

PostForum: Performance Upgrades   Posted: Tue Dec 12, 2023 10:13 am   Subject: What master cylinder for 5 lug conversion
Agree. If you use the 944 master and booster it requires rerouting of all brake lines and then the larger booster interferes with the throttle cable routing.
  Topic: Removing shaft from TT
MikeJinCO

Replies: 3
Views: 1261

PostForum: General Discussions   Posted: Tue Dec 12, 2023 3:43 am   Subject: Removing shaft from TT
Clarks Garage for 944's has a detailed write up on the shaft removal in his shop manual. It may differ slightly if you have the Porsche gear box and due to shaft sizes
  Topic: 933 D Production Auction
MikeJinCO

Replies: 2
Views: 1403

PostForum: General Discussions   Posted: Mon Nov 27, 2023 12:21 am   Subject: 933 D Production Auction
On Bring a Trailer auction site there is one of the original 16 933 D Production
cars. Apparently in storage forever.
  Topic: Starter bushing
MikeJinCO

Replies: 1
Views: 1626

PostForum: General Discussions   Posted: Tue Oct 24, 2023 9:39 pm   Subject: Starter bushing
Being a lon time since I've taken a starter apart I'd assume they are just a brass bushing. If you know the dimensions go to someone like McMaster-Carr or even the local Ace Hardware. I would doubt e ...
  Topic: 924 clutch pilot bearing
MikeJinCO

Replies: 2
Views: 1752

PostForum: General Discussions   Posted: Sat Oct 21, 2023 10:00 am   Subject: 924 clutch pilot bearing
If I recall correctly the pilot bearing is the same as a Mustang II available at any parts store.
  Topic: Sunroof Drains
MikeJinCO

Replies: 3
Views: 2089

PostForum: General Discussions   Posted: Mon Sep 11, 2023 11:58 pm   Subject: Sunroof Drains
Maybe finally go it figured out. It apears most factory tops were metal, mine is unframed glass so probably a later model Saratoga top, so an add on with no drains. One semi cure is to appy some wea ...
  Topic: Sunroof Drains
MikeJinCO

Replies: 3
Views: 2089

PostForum: General Discussions   Posted: Fri Sep 08, 2023 10:52 pm   Subject: Sunroof Drains
Two of us spent quite a while looking for drain holes in the back and couldn't find any. Removed the rubber seal and cleaned the channel. Much more difficult to get to the front. Possibly the '77's ...
  Topic: Sunroof Drains
MikeJinCO

Replies: 3
Views: 2089

PostForum: General Discussions   Posted: Wed Sep 06, 2023 11:31 pm   Subject: Sunroof Drains
Could someone post or email me a picture of the location of the sunroof drain tube holes. My car got resprayed prior to my purchase and I have never found the drain holes. It obviously leaks.
  Topic: Is this a good deal?
MikeJinCO

Replies: 11
Views: 2626

PostForum: General Discussions   Posted: Mon Aug 28, 2023 9:38 pm   Subject: Is this a good deal?
I've sent you a PM
  Topic: Source for Alternator and AC bracket bushings
MikeJinCO

Replies: 1
Views: 2405

PostForum: General Discussions   Posted: Thu Aug 10, 2023 11:44 pm   Subject: Source for Alternator and AC bracket bushings
I have some AC/Alternator brackets and bushings that I pulled off a 931S2 motor. I have no idea if it would work for you. I could send it for the cost of shipping. It will all fit in a small or med ...
  Topic: Interesting Failure
MikeJinCO

Replies: 7
Views: 692

PostForum: 924 Racing Today   Posted: Sun Jul 30, 2023 5:00 am   Subject: Interesting Failure
I continually had oil leakage problems due to not having an extension also So my solution to not having the extension was make my own. When the block was clean I reinforced the area around the dipst ...
 
Page 1 of 67 Goto page 1, 2, 3 ... 65, 66, 67  Next
All times are GMT + 10 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group