Author |
Message |
Topic: Looging for G31 center housing to differential housing seal |
Herr-Kuhn
Replies: 5
Views: 4991
|
Forum: 931 Tech. Posted: Mon Mar 16, 2015 4:24 am Subject: Looging for G31 center housing to differential housing seal |
Where did you get the selector sleeves? Are these still available? I do have 2 boxes so we should be able to select the best parts I hope. This has been a real issue to track the parts down but not ... |
Topic: Looging for G31 center housing to differential housing seal |
Herr-Kuhn
Replies: 5
Views: 4991
|
Forum: 931 Tech. Posted: Sun Mar 15, 2015 4:34 am Subject: Looging for G31 center housing to differential housing seal |
I wasn't sure on the stack up on the parts. I'm wondering if I can use the loctite sealant that the 996 use on the cam covers as this has more body than the 573.
I will have the last 2 syncro ring ... |
Topic: Looging for G31 center housing to differential housing seal |
Herr-Kuhn
Replies: 5
Views: 4991
|
Forum: 931 Tech. Posted: Wed Mar 11, 2015 11:13 am Subject: Looging for G31 center housing to differential housing seal |
477.301.191.A
Does anybody have a good one? These are NLA at the dealer, I checked stateside and in Europe. I suppose that eventually all 924/944 and 928 parts will go NLA.
Thanks,
JK |
Topic: G31 and 016Y |
Herr-Kuhn
Replies: 11
Views: 8135
|
Forum: 931 Tech. Posted: Mon Mar 09, 2015 8:54 am Subject: G31 and 016Y |
I received the Albins dog teeth for 1st and 2nd this weekend along with the pistons and rods for the AAN rebuild. There is much work to do but I hope to score down the syncros I need to complete the ... |
Topic: G31 and 016Y |
Herr-Kuhn
Replies: 11
Views: 8135
|
Forum: 931 Tech. Posted: Thu Feb 26, 2015 2:46 am Subject: G31 and 016Y |
I plotted out the gearing charts on this G31 with 016 3rd and 4th gears and I get the following at 7,000 RPM with 928S4 wheels and tires:
1st 34 MPH
2nd: 61 MPH
3rd: 98 MPH
4th: 135 MPH
5th: 18 ... |
Topic: G31 and 016Y |
Herr-Kuhn
Replies: 11
Views: 8135
|
Forum: 931 Tech. Posted: Tue Feb 24, 2015 9:06 am Subject: G31 and 016Y |
Yes, the goal is to use the entire G31 as the basis. I would like a taller 1st gear, but that is not an option as the gear is on the main-shaft in that box. I want the larger input shaft on the G31 ... |
Topic: G31 and 016Y |
Herr-Kuhn
Replies: 11
Views: 8135
|
Forum: 931 Tech. Posted: Mon Feb 23, 2015 12:58 pm Subject: G31 and 016Y |
1977.5 924. Will be grafting in the supports for the trans (I may hang from chassis, not certain yet) and running the later cast swing arms (those mounts will need to be custom as well) with the earl ... |
Topic: G31 and 016Y |
Herr-Kuhn
Replies: 11
Views: 8135
|
Forum: 931 Tech. Posted: Mon Feb 23, 2015 7:42 am Subject: G31 and 016Y |
Greetings.
Time permitting I have been pecking at my 924-Audi AAN turbo conversion project. Somewhere between building many turbo 928s and my Audi AAN powered S4 sedan the 924 project was put way ... |
Topic: 1977.5 Audi AAN Project |
Herr-Kuhn
Replies: 21
Views: 55337
|
Forum: Engine Transplants Posted: Sat Dec 20, 2014 9:20 am Subject: 1977.5 Audi AAN Project |
Been horrifically busy with 928 Twin Turbo builds this year. I do have the AAN block torn down and tanked. I am deciding if I just want to overbore it to 82mm or Nikasil plate the block back to 81mm ... |
Topic: 016Y gears in G31 |
Herr-Kuhn
Replies: 3
Views: 3758
|
Forum: 931 Tech. Posted: Thu Jul 18, 2013 12:11 pm Subject: 016Y gears in G31 |
I have secured down my 016Y (found one local) and the G31.02 has been here for a while. I've talked with many people on about this conversion and while the 5R trans and tube would do right in, I real ... |
Topic: smoke out of the breather/ catch tank + picture |
Herr-Kuhn
Replies: 13
Views: 9112
|
Forum: 931 Tech. Posted: Sat Jul 13, 2013 3:14 am Subject: smoke out of the breather/ catch tank + picture |
Consider installing a Provent air-oil separator on the car to help get rid of some of that oil. You can then recycle the collected oil by allowing it to gravity drain down back into the crankcase. T ... |
Topic: 016Y gears in G31 |
Herr-Kuhn
Replies: 3
Views: 3758
|
Forum: 931 Tech. Posted: Sat Jul 13, 2013 3:10 am Subject: 016Y gears in G31 |
Can anybody on here tell me if the 2-5th gears on the 016Y will directly integrate into a G31.02 box? I'm looking to pick up another transmission to space out 2-5th gears for a wider more powerful en ... |
Topic: Custom turbo header group buy? |
Herr-Kuhn
Replies: 48
Views: 24177
|
Forum: Performance Upgrades Posted: Fri Apr 12, 2013 1:00 am Subject: Custom turbo header group buy? |
You will need a brace on that header to avoid cracking. Hanging an 11 lb turbo from it may cause issues with longevity. You might consider making the header from weld-els (sch 10 or sch 40) to make ... |
Topic: Fitting Aluminium Control Arms to 1977 Torsion Bar Tube |
Herr-Kuhn
Replies: 29
Views: 15604
|
Forum: Performance Upgrades Posted: Wed Mar 20, 2013 4:31 am Subject: Fitting Aluminium Control Arms to 1977 Torsion Bar Tube |
My rear suspension is directly off of an 87 924S, so then I should be fine. It is still sitting out in the storage shed. I just want to get a 225 in the back with some good compound rubber. Doing a ... |
Topic: Fitting Aluminium Control Arms to 1977 Torsion Bar Tube |
Herr-Kuhn
Replies: 29
Views: 15604
|
Forum: Performance Upgrades Posted: Tue Mar 19, 2013 11:30 pm Subject: Fitting Aluminium Control Arms to 1977 Torsion Bar Tube |
So if I do fit the aluminium arms, will this be too wide for me to place an 8" rim under the back of the car? I was of the understanding that the arms were the same track width as the steel arms ... |
|