Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 139 matches
924Board.org Forum Index
Author Message
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Sat Apr 04, 2020 1:25 pm   Subject: 1979 924 Daily driven project
Finally got some mail in today, allowing me to move forward a bit. New pilot bearing insert/seal/bearing, RMS, oil pan gaskets, clutch kit, hardware. The pilot bearing going in was easier than I was a ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Wed Apr 01, 2020 6:59 am   Subject: 1979 924 Daily driven project
Do they also carry the seal as well?
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Wed Apr 01, 2020 4:01 am   Subject: 1979 924 Daily driven project
You talking about these?

https://i.ibb.co/nkxgdyt/91543968-226037971839187-2821660880586932224-n.jpg
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Tue Mar 31, 2020 11:35 am   Subject: 1979 924 Daily driven project
Another small update: CV axles are painted and ready for grease. I'm still trying to find an end cap. The ones I ordered were 128 mm, and the ones on our cars are 100mm. The only 100mm end caps I coul ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Tue Mar 31, 2020 11:28 am   Subject: 1979 924 Daily driven project
So here are some pictures to illustrate how it worked out. It actually came out incredibly easy this way. No hammering or anything destructive. I simply put play-dough back behind the threaded part at ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Mon Mar 30, 2020 12:32 pm   Subject: 1979 924 Daily driven project
I got it figured out. It uses the grease/bread/play-dough with the threaded bolt. I had to pack the play-dough behind the threads and then screwed a bolt in to get it to press it out. After fiddling w ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Mon Mar 30, 2020 10:09 am   Subject: 1979 924 Daily driven project
So I tried the grease, and I used another clutch alignment tool that was from a different project with no success. I also read that the back of the insert is threaded, so I made my own sort of jig tha ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Mon Mar 30, 2020 5:07 am   Subject: 1979 924 Daily driven project
I have a rear main coming in the mail . Also did you try the grease and hammer method; did it work for you?
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Sun Mar 29, 2020 1:39 pm   Subject: 1979 924 Daily driven project
So I'm at the point of needing to remove the pilot bearing in the crank, and I've been reading how to remove it for a while now but I don't really understand a few of the methods. Someone suggested pa ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Sun Mar 29, 2020 1:34 pm   Subject: 1979 924 Daily driven project
CV axles also getting cleaned up and ready for new boots and grease. Standby on the end cap situation. I've ordered some parts and will be trying a few things.


https://i.ibb.co/6yxWw8s/91092314-2 ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Sun Mar 29, 2020 1:28 pm   Subject: 1979 924 Daily driven project
I've been cleaning parts for the last few days so I'll just show some before and after pictures. I found some black plastic looking pieces in the oil pan and used a pick to clean a bunch of chunks out ...
  Topic: New 924 GTP build
DZGunner

Replies: 8
Views: 448

PostForum: General Discussions   Posted: Sat Mar 28, 2020 4:34 am   Subject: New 924 GTP build
Am I imagining things or is that and alternator mounted behind the transaxle?
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Thu Mar 26, 2020 11:46 am   Subject: 1979 924 Daily driven project
I have a couple questions for you guys. I took off my CV axle shafts today so I can service them, and this is the first time I've found these to not have the end cap covers on them. Are these supposed ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Thu Mar 26, 2020 4:25 am   Subject: 1979 924 Daily driven project
Yes it has a factory TPS mount on it. I bought it with a used TPS already on it; you can see it with the 6 pin connector. I'm not sure what size the butterfly valves are but when it arrives I'll look ...
  Topic: 1979 924 Daily driven project
DZGunner

Replies: 31
Views: 1247

PostForum: General Discussions   Posted: Wed Mar 25, 2020 9:42 am   Subject: 1979 924 Daily driven project
Peep has included all needed parts for his EFI/waste spark kit, so I should be good, I appreciate that offer though.

Here is a picture of the kit off his Facebook.
https://i.ibb.co/pf8gxC5/137310 ...
 
Page 1 of 10 Goto page 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  Next
All times are GMT + 10 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group